• Ergonomic design
• Aimpoint T-1 Mount and H-1 Mount provide a solid bolt on squeeze rail mounting system with a single recessed side bar and recessed socket head cap screw. 
• The Aimpoint Mount includes a custom prepared lens cover for the objective lens and an integral lens cover for the ocular end of the scope.
• The Aimpoint T-1/H-1 scopes easily install onto the T-1 Mount and the H-1 Mount with four 3mm screws. The installation wrench is included.
• Designed to mount directly to the AR-15/M16 upper receiver’s dovetail. This location places the red dot just above the front sight post.
• The Aimpoint T-1 Mount is low enough to allow co-witnessing with sights like the GG&G A2 BUIS and MAD BUIS.
• The T-1/H-1 Mount With Lens Covers is manufactured from solid billet 6061 T-6 aluminum.
• All aluminum parts are Type III hard coat anodized matte black per mil-spec.

Quick Detach Harris Bipod Adapter:

 If you have a requirement to quickly remove your Harris Bipod from your weapon, our Quick Detach Harris Bipod Adapter will meet that requirement. It provides you with the tactical flexibility to operate with our without your bipod, and to do so with just a throw of the Accu-Force Lever on our QD Harris Bipod Adapter.  

Quick Detach Harris Bipod Adapter Specifications:

• Overall design provides smooth integrated appearance and solid clamping engagement.
• QD Bipod interface surface makes full contact with Harris Bipod for a tight and solid fit.
• The Quick Detach Harris Bipod Adapter uses a standard swivel (stud) interface that is locked in a stationary position.
• Ergonomic QD lever and lever mechanism provides quick & easy on-off transition.
• The Accu-Force QD System is fully adjustable for worn or out of spec dovetails.
• The body is manufactured from billet 6061 T-6 aluminum.
• The Accu-Force Quick Detach mechanism is manufactured from 4130 steel.
• All aluminum parts are Type III hard anodized matte black per mil-spec.
• All steel parts are manganese phosphated matte black per mil-spec.
• Weighs 3.25 ozs.

Feel free to ask all the question you have. We take the time to answer them all!

The Special Purpose Rifle (SPR) has gained in popularity with shooters in the civilian and law enforcement community. Our technical advisors advised us that the scope most often used on SPR rifles is a 30mm low powered variable optic placed forward on the AR-15/M16 flattop receiver. To meet the specific optic mounting needs of the SPR shooters, we have introduced our new FLT Scope Mount With 30mm Integral Rings.

To provide flexibility to the end user, we are offering the FLT Scope Mount in two configurations; one is the Accucam QD model for those shooters requiring the ability to quickly remove or install their scope with 1/2 MOA repeatability, and the other is a semi-permanent bolt on installation, using a standard squeeze rail configuration side bar and 1/2" hex nuts. Both offer forward scope mounting. For comparative purposes the SPR Scope Mount places the scope forward 1.5 inches more than the GG&G AC-30 Scope Mount. The FLT Mount is lightweight weighing in at only 5.5 ounces, and is 5 inches long. It is low profile allowing excellent cheek weld when mounted to the AR-15/M16 flattop upper receiver. The height from the centerline of the 30mm integral rings to the top of the dovetail mounting platform is 1.460 inches. The center to center dimension of the rings is 3.750 inches. Both models are manufactured from 6061 T6 aluminum and Type III hard anodized matte black to mil-spec.

The FLT Accucam Quick Detach Scope Mount provides you with a solid method to quickly install or remove the scope from the weapon. The scope can quickly be installed on a dovetail rail in seconds by rotating the Accucam Lever to the locked position and can just as quickly be removed by rotating the Accucam Cam Lever to the unlocked position. Unlike other QD lever systems, it is fully adjustable to fit Weaver and MIL-STD-1913 dovetails, even those that are worn or out-of-spec. The ergonomic finger loop of the lever is easily operated, even with a gloved hand, and the round design is virtually snag proof. The Accucam mechanism is manufactured from solid billet 4140 steel. The QD FLT is not recommended for .50BMG or lightweight machine guns.

We think the Aimpoint Micro T-1 and H-1 are great tactical scopes; however, they have a downside. The scope design does not accommodate flip-up lens covers; thus you cannot purchase any that fit. Yes they come with the bikini lens covers, but most individuals will lose those in the first month, and they are not the easiest lens covers to remove, keep in place or reinstall.

GG&G has a very unique solution, so unique that it has a patent pending. An Accucam Quick Detach T-1 and H-1 Mount which includes a built-in provision that provides for the installation of a flip-up lens cover for the ocular end. In addition to the ocular lens cover being included, the kit also includes a specially prepared flip up lens cover that fits the objective lens. The Aimpoint QD T-1/H-1 Mount easily and solidly installs onto the lightweight GG&G Accucam QD mount with four 3mm screws. The installation wrench is included in the kit. The ocular end of the T-1 and H-1 scopes fit perfectly into the small integral lens cover flange, and while providing the means to mount a flip up lens cover, it does not interfere with the field of view. The T-1 and H-1 mount is manufactured from solid billet 6061 T6 aluminum and is Type III hard coat anodized matte black per mil-spec. The GG&G Aimpoint T-1 QD Mount is manufactured to mount directly to the AR-15/M16 integral rail. This will position the red dot just above the front sight post, yet is low enough to co-witness with the GG&G MAD, A2, or Spring Actuated A2 BUIS.

The GG&G Accucam QD Locking Lever System provides you with a solid method to quickly install or remove the Aimpoint T-1 from the weapon. The scope can quickly be installed on a dovetail rail in seconds by rotating the Accucam Lever to the locked position. It can then be quickly removed by rotating the Accucam Cam Lever to the unlocked position. Unlike other QD lever systems, it is fully adjustable to fit Weaver and MIL-STD-1913 dovetails. Not recommended for .50 BMG or lightweight machine guns. The patented Accucam design allows you to adjust the tension to accommodate out of spec or worn dovetails. The ergonomic finger loop of the lever is easily operated, even with a gloved hand, and the round design is virtually snag- proof. The Accucam mechanism is manufactured from solid billet 4140 steel and manganese phosphated matte black per mil-spec.

The Accucam Scout Length Mounting Base was designed to mount easily onto the integral rail of the AR15/M16 flat top receiver and interface with our MAD or both of our A2 Style BUIS flip-up rear sights. Manufactured to MIL-SPEC-1913, the Accucam Scout Length Mounting Base raises the line of sight by 1/2-inch, offering a proper cheek weld when optical devices are attached. The quick detachable scope mount rail extends two inches beyond the end of the receiver and clears the M4 forearm.

It was developed to accommodate "scout" type scopes, long body scope tubes, and night vision compatible red dot sights with night vision monoculars mounted to their rear. Once the optic is mounted, the integrated Accucam Quick Detach Lever System provides the shooter with the ability to quickly remove the scope in order to utilize other optics as the mission may require, and have the confidence of 1/2 MOA repeatability upon re-installation.

As with all GG&G products, the QD Scout Rail is designed and manufactured to meet the rigors of combat and professional use. The Accucam Scout Length Mounting Base is manufactured from solid billet 6061 T6 aluminum alloy and has a Type III hard coat anodized matte black mil-spec finish. All edges have been dehorned to protect the operator. The base can be quickly installed on a dovetail rail in seconds by rotating the Accucam Cam Lever to the locked position. It can then be quickly removed by rotating the Accucam Cam Lever to the unlocked position. Unlike many quick detachable scope mounts, it is fully adjustable to fit Weaver and MIL-STD 1913 dovetails. The patent pending design allows you to adjust the tension to accommodate out of spec or worn dovetails. It is not recommended for .50 BMG or lightweight machine guns.

In tests, the Accucam Locking Lever System has shown to be repeatable to 1/2 MOA. The unique finger loop lever is easily operated, even with a gloved hand, and the rounded design is ergonomic and virtually snag proof. The Accucam mechanism is manufactured from solid billet 4140 steel and manganese phosphated matte black per mil-spec.

With the development of our proprietary patented Accucam Quick Detach Locking Lever System, we are now able to fill many Quick Detach (QD) scope mount requirements. The Accucam QD Standard Base is five inches long with its rail manufactured to MIL-STD-1913. It adds 1/2 inch to the height of the mounting platform.

The GG&G Standard Base is designed and manufactured to meet the rigors of combat and professional use but is not recommended for .50 BMG or lightweight machine guns. It is manufactured from solid billet 6061 T6 aluminum alloy and has a Type III hard coat anodized matte black mil-spec finish. All edges have been dehorned to protect the operator.

The Accucam QD Locking Lever System provides you with a solid method to quickly install or remove the mounting base from the weapon system. The base can be quickly installed on a dovetail rail in seconds by rotating the Accucam Cam Lever to the locked position. It can then be quickly removed by rotating the Accucam Cam Lever to the unlocked position. It is fully adjustable to fit Weaver and MIL-STD-1913 dovetails. The unique design allows you to adjust the tension to accommodate out of spec or worn dovetails. Not recommended for .50 BMG or lightweight machine guns.

In tests, the Accucam Quick Detach Scope Rings with the locking lever are shown to be repeatable to 1/2 MOA. The unique finger loop design is easily operated, even with a gloved hand and the rounded design is ergonomic and virtually snag proof. The Accucam mechanism is manufactured from solid billet 4140 steel and manganese phosphated matte black per mil-spec. Quick Detach (QD) Scope Mounts and accessories are made in the USA at our Tucson, Arizona factory.

There is little doubt that a vertical foregrip for the AR-15 and M-16 has become a valued tactical accessory in military, law enforcement and civilian arenas. A vertical foregrip provides the operator with several important advantages, from diminishing muzzle climb during burst-fire sequences to simply offering a more comfortable shooting stance.

We are pleased to announce that through joint kinematics manufacturing we are now able to offer the GG&G Vertical Foregrip at a greatly reduced price while still maintaining the quality. The GG&G Vertical Foregrip for AR15 and M16 rifles has always provided more than the standard vertical grips. It is made of the highest quality materials and features and a core with a waterproof compartment to store batteries and other small items. The newly redesigned GG&G Vertical Foregrip is another step up-offering three great additional features at a greatly reduced price. Not only does this vertical forend grip offer a very stable vertical grip, but the new waterproof compartment will now accommodate an AR15/M16 spare bolt. The interior of the "O" ring sealed waterproof compartment has been re-configured to securely hold the bolt in place - NO RATTLES HERE.

Another new feature of this forward grip is that you no longer need a tool or coin to gain access to the waterproof compartment. The waterproof compartment cap has been re-designed with an ergonomic-no snag tri-grip feature. The third new feature is the addition of an alignment window to aid in the installation process.

Without the spare bolt stored, the waterproof compartment is large enough to securely hold two AA batteries and or two CR123 batteries. Three N type batteries, firing pins, ejectors, extractors or other small replacement parts for your weapon system can be stored in the compartment but the user needs to pack additional material, so as to eliminate rattling. Unlike other forward hand grips in the marketplace which are molded or injected plastic, all parts of the GG&G Vertical Foregrip are CNC machined from solid black Acetal cold polymer for durability and low heat absorption.

No special tools are needed for installation or adjustment in the field. This rugged vertical foregrip is 4.5" in length, 1.250" in diameter and only weighs 2.4 ounces. A separate "O" ring seals the threaded core from the combat environment. Every vertical hand grip (or "battle grip") from GG&G is made in the USA at our Tucson factory and guaranteed to work in some of the world's toughest environments and situations.

Flashlights attached to shoulder-mounted weaponry are a necessary requirement for urban warfare. Until now, attempting to use a tactical flashlight in conjunction with a vertical foregrip resulted in three scenarios: 1.Purchase an expensive combination vertical foregrip/flashlight. 2.While trying to maintain a grip on the vertical foregrip, attempt an uncomfortable and dangerous rotation of the grip hand to try to get the thumb high enough to engage the rear of the flashlight typically mounted at the three o'clock or nine o'clock position (strong left shooter). 3.Use an expensive and somewhat messy pig tail with a pressure pad glued to the foregrip or forearm that could hang you up at a critical time.

GG&G's staff has solved the problem of interfacing a vertical foregrip with a weapon-mounted flashlight by creating the Offset Tactical Flashlight Mount For Use With Vertical Foregrips. It places the tactical flashlight, offset to the right or left of the weapon's forearm at about 5 o'clock or 7 o'clock, respectively. This permits the operator to manipulate with the thumb, the illuminator's rocker switch laser button or rear pressure button of other tactical flashlights, while the support hand remains solidly on the vertical foregrip. This tactical light mount comes complete with both the Glock style and MIL-STD-1913 Picatinny rails. The Glock style rail can be easily removed and a short section of MIL-STD-1913 rail installed for attaching a Surefire or other small flashlight by means of a standard ring. The mounting rails are fully interchangeable. It is a lightweight accessory at only 2.7 ounces.

The Offset Tactical Flashlight Mount For Use With Vertical Foregrips can be mounted on the GG&G UFIR, or any of the GG&G Tactical Modular Forearms, or any other integrated rail system. This ambidextrous mount is attached by means of a squeeze rail. Manufactured from aircraft grade 6061 billet aluminum alloy, it has been Type III hard-coat anodized per mil-spec in a matte black combat finish.

The offset tactical flashlight mounts from GG&G are made in the USA at our Tucson, AZ factory. When purchasing any part that mounts on to your gun you want to make sure it fits perfectly as per mil spec standards, and it isn't going to rattle or move later on. On an AR-15, M16, or M4, stealth and surprise are essential, and accuracy is paramount. Every AR 15 flashlight mount from GG&G is made from top grade materials because it may be used in the field by military and police units who can't compromise the tactical advantage that comes with the right equipment.

Feel free to ask all the question you have. We take the time to answer them all!

Vertical foregrips and other accessories mounted at the 6 o'clock position on shoulder fired weapons have become prominent in military, law enforcement and civilian arenas. However, not every agency or individual for that matter, can afford or justify the purchase of a forearm assembly surrounded by multiple rails, when all they want to do is add a vertical foregrip or flashlight to the weapon.

Over ten years ago, GG&G introduced an inexpensive but mission ready Under Forearm Integrated Rail (UFIR) that permits instant installation and removal of most vertical foregrips, flashlights and numerous other accessories on the AR15/M16 weapon systems. This adapter rail can easily be installed onto the underside of an AR15 or M16 forearm, (standard or M4), using simple hand tools and a small amount of Loctite 262. The three point mounting system insures a solid, rugged mounting platform. Because our handguard rail mount follows the Picatinny Rail (MIL-STD-1913 or NATO's STANAG 2324) standard you will have no problem with accessory compatibility.

Installation does not require permanent alteration to the forearm. Detailed instructions and all of the parts required are supplied in the kit. The UFIR is manufactured from solid 6061 T6 billet aluminum alloy and is Type III hard-coat anodized matte black per mil-spec to provide combat durability. The GG&G UFIR is four inches long, provides eleven mounting cross lugs and machined to MIL-STD-1913 specifications so as to provide tactical flexibility in accessory mounting. It is lightweight too-at only 1.6 ounces.

It's now generally accepted that tactical slings should be mounted on the side of the weapon. As more and more operators require a QD Sling Swivel, GG&G started manufacturing an AR15 QD Sling Adapter that provides this mounting position to fill that specific mission requirement.

Our Front And Rear Quick deatch Sling Things are a lightweight, durable, easy-to-install and inexpensive sling mounts. Our QD Front Sling Thing installs easily onto the AR15/M16's "A-frame" front sight assembly, on either the right or left sides using socket head cap screws. Mounted high in this manner "rifle roll" is completely prevented. The Quick Detach Rear Sling Thing is designed for easy attachment to the AR15/M16 collapsible stock in the same manner. You know have a choice of either the standard 1 1/4 " QD sling swivel or the heavy duty QD model. Although the standard QD swivel provides great performance, the heavy duty model provides additional benefits like a larger quick detach button for an easier and quicker transition and a thicker wire diameter to provide a more robust sling attachment surface. Both QD sling swivels are bead blasted and manganeese phosphated in a non-reflective matte black mil-spec finish.

Manufactured from tough 6061 T6 billet aluminum alloy, the body of all of the Sling Things are Type III hard-coat anodized in a matte black combat finish. Our Quick Detach Sling Things are compatible with the Surefire Millenium 500 flashlight forearm.

All of GG&G's sling mounts and sling adapters for the AR15 and M16 are made in the USA at our Tucson Arizona factory to the specifications of military and police forces who use them in the field.